Subwoofer Crossover Calculator

Topic	Information
What is a subwoofer crossover?	A subwoofer crossover is a component that filters and directs specific frequency ranges to the subwoofer, ensuring it reproduces low-frequency sounds effectively.
Crossover Frequency Range	Typically ranges from 20Hz to 200Hz, with common starting points around 80Hz. This setting determines which frequencies are sent to the subwoofer.
How to Set the Crossover	Adjust the crossover frequency based on your main speakers’ capabilities, room acoustics, and personal preferences. Fine-tuning is often necessary for optimal results.
Matching Speakers to Crossover	Choose a crossover frequency that complements your main speakers and prevents overlap or gaps in frequency response.
Effects of Setting Crossover Too High	May result in a lack of bass reinforcement, causing an unbalanced sound with weak low frequencies.
Achieving Punchy Bass	Proper subwoofer placement, crossover tuning, and room treatment can help achieve punchy bass.
Low Pass Crossover Setting	Typically set around 80Hz as a starting point but can vary based on your setup.
Subwoofer dB Level Setting	Adjust the subwoofer’s volume level to blend seamlessly with the main speakers, avoiding overpowering or distortion.
Matching Amp to Subwoofer	Ensure the amplifier provides sufficient power for the subwoofer’s specifications, including impedance (ohms) and RMS power handling.
Higher vs. Lower Crossover Frequency	The ideal crossover frequency varies but is typically not higher than 200Hz. A well-balanced crossover is more important than simply choosing a high frequency.
Best Subwoofer Settings	The best settings depend on your equipment, room, and preferences. Experimentation is key to finding the optimal setup.
Reasons for Setting Crossover to 80Hz	80Hz is often used as a starting point because it aligns with the typical frequency response of many speakers and provides a balanced sound.
Impact of Crossover on Sound Quality	A properly set crossover improves sound quality by preventing speakers from reproducing frequencies they can’t handle, reducing distortion.
Frequency for a 12-inch Subwoofer	Typically capable of handling frequencies in the range of 20Hz to 200Hz.
Consistency of Crossover Frequency	Crossover frequencies should be tailored to each speaker’s capabilities and should not necessarily be the same for all speakers.
Crossover Frequency as a Percentage	Crossover frequencies are typically expressed in Hertz (Hz) and are not usually represented as percentages.
Subwoofer Phase Setting (0 or 180)	Experiment with both phase settings (0 and 180 degrees) to determine which results in better bass integration with main speakers.
Effect of Crossover on Volume	Adjusting the crossover can affect the volume balance between the subwoofer and main speakers.
Creating Deeper Bass	Achieve deeper bass through subwoofer placement, room acoustics, and adjusting crossover and subwoofer settings.
Frequency for Punchy Bass	Punchy bass can be achieved by focusing on frequencies between 40Hz and 80Hz and optimizing subwoofer settings.
Difference Between Thumpy and Punchy Bass	Thumpy bass is often slower and less defined, while punchy bass is quick, tight, and impactful.
Subsonic Filter Setting for Subwoofer	Set the subsonic filter to prevent the subwoofer from reproducing frequencies below its capabilities; common starting point is around 20Hz.
dB Level for Bass	There’s no specific dB level for bass; it should be balanced with the rest of the audio to avoid distortion.
Hz and dB for Bass Boost	Adjust bass boost settings based on your equipment and preferences, often in the range of +3dB to +6dB between 40Hz and 80Hz.
Ideal dB for Kick and Bass	Balance the kick and bass to achieve a cohesive low-end; the ideal level varies depending on the music and mix.
2 Ohm vs. 4 Ohm Subwoofers	A 2-ohm subwoofer can potentially hit harder than a 4-ohm subwoofer when matched with an appropriate amplifier.
Amp Size for 2 12-inch Subs	Choose an amplifier that matches or exceeds the combined RMS power handling of the two 12-inch subs.
Signal-to-Noise Ratio for Subwoofer Amp	A good signal-to-noise ratio for a subwoofer amplifier is generally 90dB or higher for cleaner sound.
Effect of Lower Crossover on Bass	Lowering the crossover frequency can send more bass to the subwoofer but doesn’t guarantee better bass quality; balance is crucial.

FAQs

What should subwoofer crossover be set at? The ideal subwoofer crossover setting can vary depending on your specific audio system and personal preferences, but a common starting point is around 80Hz. From there, you can fine-tune it based on your speakers and room acoustics.

How do you calculate subwoofer crossover? Crossover frequency selection isn’t typically calculated but rather determined through experimentation and listening tests. You should consider factors like the frequency response of your main speakers and the room’s acoustics when making this decision.

What should my crossover frequency be? As mentioned earlier, a starting point is around 80Hz, but the ideal crossover frequency can vary. Experiment by adjusting it while listening to music to find the frequency that provides a smooth transition between your main speakers and subwoofer.

What happens if you set the crossover too high? If you set the crossover too high, you may end up with a gap in your audio response, where the subwoofer doesn’t effectively cover the lower frequencies of your main speakers. This can result in a lack of bass and an unbalanced sound.

How do you get a punchy bass on a subwoofer? To achieve punchy bass, ensure your subwoofer is correctly placed and set up, experiment with crossover settings, and consider using a quality amplifier. Room acoustics and speaker placement also play a crucial role in achieving punchy bass.

What should I set my low pass crossover to on my subwoofer? A common starting point is around 80Hz for the low pass crossover on your subwoofer. However, fine-tune it based on your main speakers, room acoustics, and personal preferences.

What dB level should I set my subwoofer? There’s no specific dB level for setting your subwoofer because it depends on your listening environment and personal preference. Aim for a level that complements your main speakers without overpowering them or distorting the sound.

How do I match my amp to my subwoofer? To match your amp to your subwoofer, consider the subwoofer’s impedance (ohms) and the amp’s power output. Ensure that the amp can provide enough power to drive the subwoofer effectively and avoid underpowering or overpowering it.

Is a higher crossover frequency better? Not necessarily. A higher crossover frequency may result in less bass reinforcement from the subwoofer, which can lead to a less immersive audio experience. It’s essential to find the right balance between your main speakers and subwoofer.

What are the best subwoofer settings? The best subwoofer settings depend on your specific equipment, room, and personal preferences. Experiment with crossover frequency, phase, and volume to achieve the best results for your setup.

Why set crossover to 80Hz? Setting the crossover to 80Hz is a common starting point because it aligns with the typical frequency response of many home theater and bookshelf speakers. However, the ideal crossover frequency can vary based on your specific setup.

Does a crossover improve sound quality? Yes, a crossover helps improve sound quality by ensuring that each speaker in your audio system reproduces the frequencies it’s designed for. This prevents speakers from playing frequencies outside their range, reducing distortion and providing a cleaner sound.

What is the best frequency for a 12-inch subwoofer? The best frequency for a 12-inch subwoofer depends on various factors, including the subwoofer’s design and your listening preferences. Typically, a frequency range of 20Hz to 200Hz is common for 12-inch subwoofers.

Should crossover be the same for all speakers? No, the crossover settings should not be the same for all speakers because different speakers have different frequency response characteristics. Each speaker should have a crossover setting tailored to its capabilities.

Can crossover frequency be over 50%? Crossover frequencies are typically specified in Hertz (Hz) and are not typically expressed as percentages. You can set crossover frequencies to any value within the range supported by your audio equipment.

Should my sub phase be 0 or 180? The subwoofer phase setting (0 or 180 degrees) depends on the phase relationship between your main speakers and subwoofer. Experiment with both settings to find the one that results in the best bass integration with your main speakers.

Does crossover affect volume? Yes, the crossover setting can affect the volume balance between your main speakers and subwoofer. Adjusting the crossover frequency can influence how much bass is sent to the subwoofer, impacting the overall volume perception.

How do I make my bass deeper? To make your bass deeper, consider using a subwoofer with a lower frequency response, proper placement, and room acoustic treatments. Adjusting the crossover and subwoofer settings can also help achieve deeper bass.

What frequency makes bass punchy? The punchiness of bass depends on various factors, including the subwoofer, room acoustics, and the music itself. A balanced combination of lower frequencies (e.g., 40-80Hz) and proper setup can result in punchy bass.

What is thumpy vs. punchy bass? “Thumpy” bass typically refers to bass that has a slow or boomy quality, while “punchy” bass is characterized by quick, tight, and impactful bass hits. Achieving punchy bass often involves better control and tuning of your subwoofer.

What is the best subsonic setting for a subwoofer? The best subsonic setting depends on your subwoofer’s specifications and your music preferences. A typical starting point is around 20Hz. Adjust the subsonic filter to prevent the subwoofer from reproducing frequencies below its capabilities.

What dB is best for bass? The best dB level for bass depends on your listening environment and personal preference. Typically, a balanced bass level that complements your main speakers without overpowering them is ideal.

What Hz and dB is best for bass boost? The best Hz and dB settings for bass boost vary based on your audio equipment and preferences. Use a subtle bass boost, such as +3dB at a frequency between 40Hz and 80Hz, as a starting point.

What dB should kick and bass be? The ideal dB level for kick and bass depends on the specific track and your mixing preferences. Balance them to achieve a cohesive and impactful low end in your music.

What hits harder, 2 ohm or 4 ohm? All else being equal, a 2-ohm subwoofer will generally hit harder than a 4-ohm subwoofer because it allows the amplifier to deliver more power to the subwoofer.

What size amp do I need for 2 12-inch subs? The size (power rating) of the amplifier you need for two 12-inch subs depends on the subs’ specifications and the desired sound level. A common recommendation is an amplifier with a power rating that matches or exceeds the combined RMS power handling of the subs.

What is a good signal-to-noise ratio for a subwoofer amplifier? A good signal-to-noise ratio for a subwoofer amplifier is typically 90dB or higher. Higher values indicate less background noise and cleaner sound.

Does a lower crossover mean more bass? Not necessarily. A lower crossover setting may send more bass to the subwoofer, but it doesn’t guarantee better bass quality. The ideal crossover setting depends on various factors, including your main speakers and room acoustics.

How do I set my amp gain for subs? To set your amp gain for subs, use a multimeter or an oscilloscope to measure the output voltage of your head unit. Adjust the gain until you achieve the desired voltage without distortion.

Is an 80Hz crossover good? An 80Hz crossover is a common starting point and often works well for many setups. However, whether it’s “good” depends on your specific equipment and room acoustics. Experiment to find the best crossover frequency for your system.

What subwoofer has the deepest bass? Subwoofers with larger cone diameters, such as 15-inch or 18-inch models, are generally capable of producing deeper bass. However, factors like enclosure design and subwoofer quality also play a significant role.

Should the sub be louder than bass? The subwoofer should complement the bass from your main speakers, but it doesn’t necessarily need to be louder. The goal is to achieve a balanced and cohesive sound that suits your preferences.

What does crossover distortion sound like? Crossover distortion can sound like a noticeable gap or inconsistency in the audio frequency response, especially in the transition between the subwoofer and main speakers. It may result in a lack of smooth integration between the two.

What is the best crossover frequency for rear speakers? The best crossover frequency for rear speakers depends on your specific audio system and preferences. A typical starting point is around 80Hz, but adjust it based on your rear speaker’s capabilities and your listening environment.

Do I need a crossover for my subwoofer? Yes, a crossover is essential for your subwoofer to ensure it reproduces only the desired low-frequency content and doesn’t interfere with the main speakers. Most subwoofers and AV receivers have built-in crossovers.

What sounds better, 10 or 12-inch subs? Whether 10-inch or 12-inch subs sound better depends on various factors, including the specific subwoofer models, enclosure design, and your listening preferences. Both can deliver excellent bass quality when properly matched and set up.

What frequencies to cut from sub-bass? The frequencies to cut from sub-bass depend on the source material and your mixing needs. Common cuts range from 20Hz to 40Hz to remove excessive low-frequency content that can cause muddiness.

Is 30Hz low enough for a subwoofer? 30Hz is a reasonably low frequency for a subwoofer, and it can reproduce most bass frequencies encountered in music and movies. However, some enthusiasts may prefer even lower frequencies for specific applications.

What is the best crossover for a subwoofer? The best crossover for a subwoofer depends on your specific setup. A flexible adjustable crossover on an AV receiver or subwoofer amplifier allows you to fine-tune the crossover frequency to suit your speakers and room.

How do I know if my speaker crossover is bad? Signs of a bad speaker crossover may include distorted or unbalanced sound, diminished bass or treble response, and abnormal noise from the speaker. If you suspect a bad crossover, it may need repair or replacement.

What is the default crossover frequency? There is no universal default crossover frequency as it varies among audio equipment and speakers. You may find 80Hz as a common starting point in many AV receivers and subwoofers, but it’s not a strict default.

What does an 80Hz crossover mean? An 80Hz crossover setting means that frequencies below 80Hz are sent to the subwoofer, and frequencies above 80Hz are sent to the main speakers. It’s a common starting point for achieving a balanced audio response.

How do I know if my subwoofer is out of phase? You can check if your subwoofer is out of phase by listening for a lack of bass impact and clarity. Additionally, you can use a phase test track or a phase test tone to determine the optimal phase setting for your subwoofer.

What causes hum in a subwoofer? Hum in a subwoofer can be caused by ground loops, improper grounding, or interference from other electronic devices. Isolating and addressing the source of the hum can help eliminate it.

What does 180 degrees out of phase look like? 180 degrees out of phase means that the subwoofer’s diaphragm movement is opposite to the main speakers. Visually, it doesn’t have a specific appearance; it’s a phase relationship that affects sound quality.

What are the best crossover levels? The best crossover levels depend on your specific equipment and room acoustics. Experiment with different levels to find the one that provides a balanced and seamless audio response.

How do I set my crossover? To set your crossover, refer to your AV receiver or subwoofer’s manual and use its built-in controls to select the desired frequency. Fine-tune the crossover by listening to audio and adjusting it to your liking.

How do I get a better crossover? A better crossover can be achieved by investing in high-quality audio equipment, using room acoustic treatments, and fine-tuning your crossover settings through experimentation.

What depth do bass prefer? Bass preferences vary among listeners, but for many, a balanced and well-defined bass response is preferred. Achieving this often involves careful speaker placement, room treatments, and proper equipment setup.

How deep is too deep for bass? “Too deep” for bass is subjective and depends on personal taste and the listening environment. Extremely low frequencies (subsonic) may not be audible but can be felt. Finding the right balance is key.

What causes boomy bass? Boomy bass is often caused by poor room acoustics, improper subwoofer placement, or an excessive boost in the low-frequency range. It results in an uncontrolled, resonant bass sound.

Which Hz is responsible for bass? Bass frequencies typically range from 20Hz to 200Hz, with the lower end (20Hz to 80Hz) containing the deepest and most prominent bass notes.

Which is better, deep bass or punchy bass? Whether deep bass or punchy bass is better depends on personal preferences and the type of music or content being listened to. Some prefer deep, rumbling bass, while others prefer tight and impactful punchy bass.

How do I make my bass more punchy? To make your bass more punchy, consider using a subwoofer with fast transient response, adjust the crossover frequency, and experiment with subwoofer placement and room treatments to reduce unwanted resonances.

What is the best wave shape for sub-bass? The best wave shape for sub-bass is typically a sine wave, as it produces a pure and clean bass sound. However, the choice of wave shape can depend on the music genre and desired artistic effect.

How do I know if my bass is boomy? You can identify boomy bass by listening for a lack of control and definition in the low frequencies. It often sounds excessive and resonant, masking the clarity of the music.

What is the best phase setting for a subwoofer? The best phase setting for a subwoofer depends on your specific setup and room acoustics. Experiment with both 0 and 180-degree settings to find the one that results in the best bass integration with your main speakers.

What is the best subwoofer configuration? The best subwoofer configuration depends on your audio system and room layout. Common configurations include single subwoofers, dual subwoofers, and more advanced setups like multiple subs for optimal bass distribution.

What should I set my LPF and subsonic to? The settings for the low-pass filter (LPF) and subsonic filter depend on your subwoofer and amplifier specifications, as well as your listening preferences. Refer to the manufacturer’s recommendations as a starting point and adjust as needed.

How loud should bass be in a rock mix? The loudness of bass in a rock mix should complement the other elements of the music. It should be balanced and provide a solid foundation without overpowering vocals and other instruments.

What range should a bass have? Bass typically covers a frequency range of 20Hz to 200Hz, but the specific range can vary depending on the musical context and instrumentation.

What noise is best for blocking bass? To block bass noise, consider using thick, dense materials like mass-loaded vinyl or acoustic foam panels on walls and ceilings. Bass traps in corners can also help reduce bass reflections.

What is the best dB for bass boost? The best dB level for bass boost depends on your audio equipment and personal preference. A moderate boost, such as +3dB to +6dB, is often a good starting point.

How should I set the bass boost frequency? Set the bass boost frequency based on your audio equipment’s capabilities and your musical preferences. A common starting point is between 40Hz and 80Hz, but adjust it to suit your specific needs.

Does bass get louder with more Hz? Bass doesn’t necessarily get louder with higher Hz values. The perceived loudness of bass depends on the amplitude (volume) of the bass frequencies, not just the frequency itself.

Should kick or bass be louder? The balance between the kick and bass depends on the musical genre and mixing goals. In many cases, they should complement each other, with neither being significantly louder than the other.

Should you compress kick and bass together? Compressing the kick and bass together can be beneficial in some music genres to achieve a cohesive and controlled low end. However, it depends on the specific sound you want to achieve and the mix context.

What is the best ohm for sound quality? The best ohm rating for sound quality depends on your audio system. Generally, higher-ohm speakers (e.g., 8 ohms) can offer better sound quality with the right amplifier, but the speaker design and quality also play crucial roles.

How much louder is 2 ohms than 4 ohms? In general, a 2-ohm speaker will draw more power from an amplifier compared to a 4-ohm speaker, resulting in potentially louder output. The actual difference in loudness can vary depending on the specific equipment and power ratings.

Are 2 10-inch subs louder than 1 12-inch? Two 10-inch subs can potentially be louder than a single 12-inch sub when properly powered and configured. However, the specific outcome depends on the subwoofer models and their combined capabilities.

Do 12-inch subs hit harder than 15-inch? The size of the subwoofer alone does not determine how hard it hits. The subwoofer’s design, power handling, and enclosure play more significant roles in its performance. A well-designed 15-inch sub can hit as hard as a 12-inch sub or even harder.

Is a 70 dB signal-to-noise ratio good? A 70 dB signal-to-noise ratio may be acceptable for some audio equipment, but it’s not considered high-end. Higher signal-to-noise ratios, such as 90 dB or more, are generally preferred for better audio quality, especially in critical listening environments.

What does a high signal-to-noise ratio look like? A high signal-to-noise ratio (SNR) is typically represented as a number, such as 90 dB or 100 dB. It indicates the level of the desired audio signal (music) relative to background noise or interference, with higher values representing cleaner audio.

What is the best crossover frequency for rear speakers? The best crossover frequency for rear speakers depends on your audio system and listening preferences. A typical starting point is around 80Hz, but adjust it based on your rear speaker’s capabilities and your room acoustics.

Do I need a crossover for my subwoofer? Yes, a crossover is essential for your subwoofer to ensure it reproduces only the desired low-frequency content and doesn’t interfere with the main speakers. Most subwoofers and AV receivers have built-in crossovers.

What sounds better, 10 or 12-inch subs? Whether 10-inch or 12-inch subs sound better depends on various factors, including the specific subwoofer models, enclosure design, and your listening preferences. Both can deliver excellent bass quality when properly matched and set up.

What frequencies to cut from sub-bass? The frequencies to cut from sub-bass depend on the source material and your mixing needs. Common cuts range from 20Hz to 40Hz to remove excessive low-frequency content that can cause muddiness.

Is 30Hz low enough for a subwoofer? 30Hz is a reasonably low frequency for a subwoofer, and it can reproduce most bass frequencies encountered in music and movies. However, some enthusiasts may prefer even lower frequencies for specific applications.

What is the best crossover for a subwoofer? The best crossover for a subwoofer depends on your specific setup. A flexible adjustable crossover on an AV receiver or subwoofer amplifier allows you to fine-tune the crossover frequency to suit your speakers and room.

How do I know if my speaker crossover is bad? Signs of a bad speaker crossover may include distorted or unbalanced sound, diminished bass or treble response, and abnormal noise from the speaker. If you suspect a bad crossover, it may need repair or replacement.

What should subwoofer crossover be set at? The ideal subwoofer crossover setting can vary depending on your specific audio system and personal preferences, but a common starting point is around 80Hz. From there, you can fine-tune it based on your speakers and room acoustics.

What is the default crossover frequency? There is no universal default crossover frequency as it varies among audio equipment and speakers. You may find 80Hz as a common starting point in many AV receivers and subwoofers, but it’s not a strict default.

What does an 80Hz crossover mean? An 80Hz crossover setting means that frequencies below 80Hz are sent to the subwoofer, and frequencies above 80Hz are sent to the main speakers. It’s a common starting point for achieving a balanced audio response.

How do I know if my subwoofer is out of phase? You can check if your subwoofer is out of phase by listening for a lack of bass impact and clarity. Additionally, you can use a phase test track or a phase test tone to determine the optimal phase setting for your subwoofer.

What causes hum in a subwoofer? Hum in a subwoofer can be caused by ground loops, improper grounding, or interference from other electronic devices. Isolating and addressing the source of the hum can help eliminate it.

What does 180 degrees out of phase look like? 180 degrees out of phase means that the subwoofer’s diaphragm movement is opposite to the main speakers. Visually, it doesn’t have a specific appearance; it’s a phase relationship that affects sound quality.

What are the best crossover levels? The best crossover levels depend on your specific equipment and room acoustics. Experiment with different levels to find the one that provides a balanced and seamless audio response.

How do I set my crossover? To set your crossover, refer to your AV receiver or subwoofer’s manual and use its built-in controls to select the desired frequency. Fine-tune the crossover by listening to audio and adjusting it to your liking.

How do I get a better crossover? A better crossover can be achieved by investing in high-quality audio equipment, using room acoustic treatments, and fine-tuning your crossover settings through experimentation.

What depth do bass prefer? Bass preferences vary among listeners, but for many, a balanced and well-defined bass response is preferred. Achieving this often involves careful speaker placement, room treatments, and proper equipment setup.

How deep is too deep for bass? “Too deep” for bass is subjective and depends on personal taste and the listening environment. Extremely low frequencies (subsonic) may not be audible but can be felt. Finding the right balance is key.

What causes boomy bass? Boomy bass is often caused by poor room acoustics, improper subwoofer placement, or an excessive boost in the low-frequency range. It results in an uncontrolled, resonant bass sound.

Which Hz is responsible for bass? Bass frequencies typically range from 20Hz to 200Hz, with the lower end (20Hz to 80Hz) containing the deepest and most prominent bass notes.

Which is better, deep bass or punchy bass? Whether deep bass or punchy bass is better depends on personal preferences and the type of music or content being listened to. Some prefer deep, rumbling bass, while others prefer tight and impactful punchy bass.

How do I make my bass more punchy? To make your bass more punchy, consider using a subwoofer with fast transient response, adjust the crossover frequency, and experiment with subwoofer placement and room treatments to reduce unwanted resonances.

What is the best wave shape for sub-bass? The best wave shape for sub-bass is typically a sine wave, as it produces a pure and clean bass sound. However, the choice of wave shape can depend on the music genre and desired artistic effect.

How do I know if my bass is boomy? You can identify boomy bass by listening for a lack of control and definition in the low frequencies. It often sounds excessive and resonant, masking the clarity of the music.

What is the best phase setting for a subwoofer? The best phase setting for a subwoofer depends on your specific setup and room acoustics. Experiment with both 0 and 180-degree settings to find the one that results in the best bass integration with your main speakers.

What is the best subwoofer configuration? The best subwoofer configuration depends on your audio system and room layout. Common configurations include single subwoofers, dual subwoofers, and more advanced setups like multiple subs for optimal bass distribution.

What should I set my LPF and subsonic to? The settings for the low-pass filter (LPF) and subsonic filter depend on your subwoofer and amplifier specifications, as well as your listening preferences. Refer to the manufacturer’s recommendations as a starting point and adjust as needed.

How loud should bass be in a rock mix? The loudness of bass in a rock mix should complement the other elements of the music. It should be balanced and provide a solid foundation without overpowering vocals and other instruments.

What range should a bass have? Bass typically covers a frequency range of 20Hz to 200Hz, but the specific range can vary depending on the musical context and instrumentation.

What noise is best for blocking bass? To block bass noise, consider using thick, dense materials like mass-loaded vinyl or acoustic foam panels on walls and ceilings. Bass traps in corners can also help reduce bass reflections.

What is the best dB for bass boost? The best dB level for bass boost depends on your audio equipment and personal preference. A moderate boost, such as +3dB to +6dB, is often a good starting point.

How should I set the bass boost frequency? Set the bass boost frequency based on your audio equipment’s capabilities and your musical preferences. A common starting point is between 40Hz and 80Hz, but adjust it to suit your specific needs.

Does bass get louder with more Hz? Bass doesn’t necessarily get louder with higher Hz values. The perceived loudness of bass depends on the amplitude (volume) of the bass frequencies, not just the frequency itself.

Should kick or bass be louder? The balance between the kick and bass depends on the musical genre and mixing goals. In many cases, they should complement each other, with neither being significantly louder than the other.

Should you compress kick and bass together? Compressing the kick and bass together can be beneficial in some music genres to achieve a cohesive and controlled low end. However, it depends on the specific sound you want to achieve and the mix context.

What is the best ohm for sound quality? The best ohm rating for sound quality depends on your audio system. Generally, higher-ohm speakers (e.g., 8 ohms) can offer better sound quality with the right amplifier, but the speaker design and quality also play crucial roles.

How much louder is 2 ohms than 4 ohms? In general, a 2-ohm speaker will draw more power from an amplifier compared to a 4-ohm speaker, resulting in potentially louder output. The actual difference in loudness can vary depending on the specific equipment and power ratings.

Are 2 10-inch subs louder than 1 12-inch? Two 10-inch subs can potentially be louder than a single 12-inch sub when properly powered and configured. However, the specific outcome depends on the subwoofer models and their combined capabilities.

Do 12-inch subs hit harder than 15-inch? The size of the subwoofer alone does not determine how hard it hits. The subwoofer’s design, power handling, and enclosure play more significant roles in its performance. A well-designed 15-inch sub can hit as hard as a 12-inch sub or even harder.

Is a 70 dB signal-to-noise ratio good? A 70 dB signal-to-noise ratio may be acceptable for some audio equipment, but it’s not considered high-end. Higher signal-to-noise ratios, such as 90 dB or more, are generally preferred for better audio quality, especially in critical listening environments.

What does a high signal-to-noise ratio look like? A high signal-to-noise ratio (SNR) is typically represented as a number, such as 90 dB or 100 dB. It indicates the level of the desired audio signal (music) relative to background noise or interference, with higher values representing cleaner audio.